CONTOUR 600
ROAD MARKING MACHINE
THIN-LAYER PAINT MARKING
The Kontur 600 machine is designed for applying horizontal road markings with quick-drying paints and reflective glass beads. Its dimensions allow it to be used within city limits and on suburban highways without interfering with traffic.
The hydraulic wheel drive ensures a smooth ride, and the sight can be lowered and raised from the operator’s station, allowing the Kontur 600 to be quickly converted from transport to operational mode. The airless line application method, which can generate paint pressure up to 130 bar, allows the use of high-viscosity (up to 150 seconds on the Ford No. 4 cup) marking materials with a high solids content. These paints dry quickly and do not sag even in thick (up to 650 microns) layers.
The use of high-quality components ensures reliability and a long service life. The machine uses components from Perkins, Graco, Danfoss, Festo, Fini, and Kamber. A single load of marking material is sufficient for 1,200 m² of markings.
BASIC EQUIPMENT OF THE CAR:
- central marking unit with three pairs of paint and sprinkler guns;
- a remote button that duplicates the “Start” button on the control panel;
- side marking block to the right of the car, without guns;
- remote control for applying markings;
- a pedal that duplicates the “Start” button on the marking control panel;
- paint flow sensor;
- hand-held gun with a 10 m hose;
- flashing beacons on the roof of the car;
- searchlight for illuminating the marking block;
- operator workstation lighting;
- hydraulic drive for lifting and lowering the central marking unit;
- hydraulic drive for raising and lowering the sight;
- hand-held air gun for cleaning work equipment with air;
- rear platform for auxiliary worker and traffic cones.
ADDITIONAL EQUIPMENT OF THE MACHINE:
- joystick for accelerated selection of remote control programs;
- an additional fourth pair of paint and sprinkler guns on the
- right side marking unit;
- side marking unit to the left of the machine, without guns (cannot be installed with the “Cold Spray Plastic 100:2 external mix” option);
- photo sensor of the beginning of the line (can be installed on any gun);
- obstacle avoidance direction sign (700 mm);
- 50cm extension for hand-held paint gun;
- Cold Spray Plastic 100:2 option, external mixing, single line.
MAIN TECHNICAL CHARACTERISTICS
| Characteristic | CONTOUR 600 |
|---|---|
| Engine type | diesel |
| Engine power, kW | 44,7 |
| Engine power, hp | 61 |
| Engine capacity,cm3 | 2212 |
| Engine environmental safety class | EU Stage IIIA (TIER 2) |
| Compressor | piston |
| Maximum working road slope, % | 20 |
| Maximum road slope, % | 30 |
| Transport speed, km/h | 12 |
| Capacity for glass beads, l | 2 x 55 |
| Capacity for glass beads, kg | 170 |
| Remote control screen diagonal, inches | 5,7 |
| Number of pre-installed programs | до 24 |
| Type of marking material | paint / spray plastic 100:2 (external mixing) |
| Maximum marking speed, km/h | 7 |
| Amount of marking material, kg | 600 |
| Amount of hardener, l | |
| Amount of washing liquid, l | |
| Fuel tank capacity, l | 50 |
| Oil tank capacity, l | 75 |
| Number of lines applied simultaneously | 2 |
| Number of guns (applicators, extruding heads) | 3 |
| Width of applied lines, double, mm | up to 150 |
| Width of applied lines, single, mm | up to 300 |
| Overall dimensions of the machine (Length x Width x Height), mm: | |
| — in working position | 5200х2000х2100 |
| — in transport position | 3400х1300х2100 |
| Dry weight, kg | 1700 |
| Curb weight, kg | 1820 |
| Gross weight, kg | 2600 |