STIM MARK 10 T
ROAD MARKING MACHINE WITH THERMOPLASTIC PLASTICS
MARKING WITH THERMOPLASTICS
The main task solved by the STIM Mark 10 T marking machine is to ensure maximum equipment productivity by continuously heating a large amount of thermoplastic transported directly on the machine.
The applied material rate can reach up to 4 tons per hour. Operator workstations are equipped with control units based on industrial controllers, a video monitoring system for road conditions and the marking application process, and a remote process control and monitoring system. The marking units, with adjustable reach, can simultaneously apply markings to two lanes to the right and left of the machine. The system’s operating speed can reach 10 km/h when applying thick-layer markings and 15 km/h when applying thin-layer markings.
Integrated marking control systems allow the machine to be equipped at any time with the LIS system, designed to repeat markings with minimal operator intervention.
BASIC EQUIPMENT OF THE CAR:
- a hydraulically extendable marking unit on the left side of the machine with a 500 mm marking unit (10 elements of 50 mm each) for thick-layer marking, two guns for applying thin-layer marking, and guns for applying glass beads;
- a hydraulically extendable marking unit on the right side of the machine with a marking unit that allows for the application of structural markings of different widths, one gun for applying thin-layer markings (optional), and a gun for applying glass beads;
- Operator’s workplace:
— control panel for applying M15 markings;
— control panel for process equipment, autonomous power unit;
— video surveillance system monitors;
- driver’s workplace:
— “Vidomarker” system, video surveillance system monitor;
- marking material quantity control system:
— tanks with weight sensors;
— glass bead presence sensors;
— vacuum glass bead loading system;
— manipulator;
— conveyors for loading tanks for heating and preparing thermoplastic;
- Safety features:
— beam-type beacon on the vehicle cabin;
— light board at the rear of the vehicle;
— side lights on the marking blocks.
ADDITIONAL EQUIPMENT OF THE MACHINE:
- wireless intercoms;
- LIS system for one of the marking blocks;
- operator’s workplace in the machine cabin;
- signs “Road works”, “Speed limit 40 km/h”;
- damper device at the rear of the machine.
MAIN TECHNICAL CHARACTERISTICS
| Characteristic | STIM MARK 10 T |
|---|---|
| Chassis | Scania G 440 B8x4NZ |
| Chassis environmental class | Euro 5 |
| Chassis engine fuel | diesel |
| Chassis wheel arrangement | 8×4 |
| Marking application speed with the following paint consumption: | FASSI F65b |
| — maximum horizontal reach, m | 5,6 |
| — lifting capacity at maximum reach, t | 1,2 |
| Method of applying marking lines: | |
| — thick-layered | extrusion |
| — thin-layer (spray thermoplastic) | air |
| Marking application speed, km/h: | |
| — thick-layered | up to 10 |
| — thin-layer | up to 15 |
| Autonomous power plant: | |
| — engine power, kW | 44 |
| — engine fuel type | diesel |
| — nominal (maximum) compressor capacity, l/min | 600 (5000) |
| Capacity of containers for consumables, kg: | |
| — for thermoplastic | 2х1000 |
| — for glass beads | 2х1000 |
| The amount of thermoplastic transported to the storage area, kg | 8000 |
| Number of marking lines applied simultaneously: | |
| — on the left side of the car | 2 |
| — on the right side of the car | 1 |
| Maximum width of applied lines, mm: | |
| — two marking blocks in working position | 11800х4900х3950 |
| — in transport position | 11800х2540х3950 |
| Curb weight of the vehicle, t | 32 |
| Technically permissible weight of the vehicle, t | 48 |